• Just as you would create custom designs for cost and time saving purposes, Possess the ability to save you further time and expense by offering numerous post-extrusion magnesium product fabrication processes in-house .
• Meifu Technology specializes in the following, but are not limited to, custom magnesium fabrication capabilities.
• Advantages of Magnesium Extrusions
Compared to other types of manufactured components, magnesium extrusions offer a number of advantages, such as:
• Precisely controlled 3 intermediate-frequency induction furnaces to pre-heat the part before extrusion.
• Full set of extrusion dies: can extrude various sizes of Mg bars.
• Superior strength-to-weight ratio.
• Broad material selection.
• Wide application suitability.
• Excellent corrosion resistance.
• High thermal and electrical conductivity.
• Low cost.
| GB/T5153—2003 |
| Grades and chemical composition of wrought magnesium and magnesium alloys |
| Grade | Chemical composition (mass fraction)/% |
| Al | Zn | Mn | Ce | Zr | Ca | Be | Si | Fe | Cu | Ni | Single impurity | total impurities |
| AZ31B | 2.5-3.5 | 0.60-1.4 | 0.20-1.0 |
|
| ≤0.04 |
| ≤0.08 | ≤0.003 | ≤0.01 | ≤0.001 | ≤0.05 | ≤0.30 |
| AZ31S | 2.4-3.6 | 0.50-1.5 | 0.15-0.4 |
|
|
|
| ≤0.10 | ≤0.005 | ≤0.05 | ≤0.005 | ≤0.05 | ≤0.30 |
| AZ31T | 2.4-3.6 | 0.50-1.5 | 0.05-0.4 |
|
|
|
| ≤0.10 | ≤0.05 | ≤0.05 | ≤0.005 | ≤0.05 | ≤0.30 |
| AZ40M | 3.0-4.0 | 0.20-0.8 | 0.15-0.5 |
|
|
| ≤0.01 | ≤0.10 | ≤0.05 | ≤0.05 | ≤0.005 | ≤0.01 | ≤0.30 |
| AZ41M | 3.7-4.7 | 0.80-1.4 | 0.30-0.6 |
|
|
| ≤0.01 | ≤0.10 | ≤0.05 | ≤0.05 | ≤0.005 | ≤0.01 | ≤0.30 |
| AZ61A | 5.8-7.2 | 0.40-1.5 | 0.15-0.5 |
|
|
|
| ≤0.10 | ≤0.005 | ≤0.05 | ≤0.005 |
| ≤0.30 |
| AZ61M | 5.5-7.0 | 0.50-1.5 | 0.15-0.5 |
|
|
| ≤0.01 | ≤0.10 | ≤0.05 | ≤0.05 | ≤0.005 | ≤0.01 | ≤0.30 |
| AZ61S | 5.5-6.5 | 0.50-1.5 | 0.15-0.4 |
|
|
|
| ≤0.10 | ≤0.005 | ≤0.05 | ≤0.005 | ≤0.05 | ≤0.30 |
| AZ62M | 5.0-7.0 | 2.0-3.0 | 0.20-0.5 |
|
|
| ≤0.01 | ≤0.10 | ≤0.05 | ≤0.05 | ≤0.005 | ≤0.01 | ≤0.30 |
| AZ63B | 5.3-6.7 | 2.5-3.5 | 0.15-0.6 |
|
|
|
| ≤0.08 | ≤0.003 | ≤0.01 | ≤0.001 |
| ≤0.30 |
| AZ80A | 7.8-9.2 | 0.20-0.8 | 0.12-0.5 |
|
|
|
| ≤0.10 | ≤0.005 | ≤0.05 | ≤0.005 |
| ≤0.30 |
| AZ80M | 7.8-9.2 | 0.20-0.8 | 0.15-0.5 |
|
|
| ≤0.01 | ≤0.10 | ≤0.05 | ≤0.05 | ≤0.005 | ≤0.01 | ≤0.30 |
| AZ80S | 7.8-9.2 | 0.20-0.8 | 0.12-0.4 |
|
|
|
| ≤0.10 | ≤0.005 | ≤0.05 | ≤0.005 | ≤0.05 | ≤0.30 |
| AZ91D | 8.5-9.5 | 0.45-0.9 | 0.17-0.4 |
|
|
| 0.0005-0.003 | ≤0.08 | ≤0.004 | ≤0.025 | ≤0.001 | ≤0.01 |
|
| M1C | ≤0.01 |
| 0.50-1.3 |
|
|
|
| ≤0.05 | ≤0.01 | ≤0.01 | ≤0.001 | ≤0.05 | ≤0.30 |
| M2M | ≤0.20 | ≤0.30 | 1.3-2.5 |
|
|
| ≤0.01 | ≤0.10 | ≤0.05 | ≤0.05 | ≤0.007 | ≤0.01 | ≤0.20 |
| M2S |
|
| 1.2-2.0 |
|
|
|
| ≤0.10 |
| ≤0.05 | ≤0.01 | ≤0.05 | ≤0.30 |
| ZK61M | ≤0.05 | 5.0-6.0 | ≤0.10 |
| 0.30-0.90 |
| ≤0.01 | ≤0.05 | ≤0.05 | ≤0.05 | ≤0.005 | ≤0.01 | ≤0.30 |
| ZK61S |
| 4.8-6.2 |
|
| 0.45-0.80 |
|
|
|
|
|
| ≤0.05 | ≤0.30 |
| ME20M | ≤0.20 | ≤0.30 | 1.3-2.2 | 0.15-0.35 |
|
| ≤0.01 | ≤0.10 | ≤0.05 | ≤0.05 | ≤0.007 | ≤0.01 |
|
